水分蒸发量:最大3000ml/h 粒径:40-100微米
Yamaoto大容量喷雾干燥箱 DL410
可生成一般实验装置很难实现的40~100μm细粒的喷雾干燥装置。
● 操作和显示均采用触摸屏,对话框方式,操作简单。可利用触摸屏进行日语、英语、中文的切换。鼓风机、送液泵、喷嘴吹风、探针敲击、头部上升下降的动作都能通过触摸屏进行操作。
●入口温度以及出口温度的测定温度将显示在数码温度调节器上。
●采用高效率喷雾方式(二流体喷嘴方式)和大型干燥腔,相比以前产品,样品的附着量减少,回收率更高。
●干燥腔、旋风部、收集容器采用的超硬玻◆璃制品,能够很好的掌握喷嘴的喷雾状态和粒体〇的动作。
●喷嘴上,采用了利用定时器在设定时间对筛眼进行清扫的自动结构。
●将干燥腔大容量化,设计上能够确保生成微细粒的必要干燥时间。因此,能够生成与◥陶瓷等的成型用粉体、医药品食品等各行业的生产装置所生产的制品近似的40~100μm微细粒。
●鼓风机●采用寿命长的DC无刷马达。
● 标配有除静电刷,使得收集容器内的生成物回收效率良好。
在喷雾干燥器使用有机溶剂时,为了不向外部排出,配套使用有机溶剂回收装@置,形成高安全性的氮气密闭循环方式。
YAMATO有机溶剂回收装置型号: GAS410
■规格
型号 |
DL410 |
||
性能 |
水分蒸发量 |
Max. 3000ml/h |
|
喷雾方式 |
二流体喷嘴方式(筛眼径0.7mm) |
||
喷雾、热风接触方式 |
下方喷雾并流方式 |
||
送液泵 |
定量送ξ 液泵,流量到70ml/min可变 |
||
吸气鼓风机 |
DC无刷马达,0.3~1.0m3/min |
||
温度控制方式 |
PID控制 |
||
温度调节器设定范围 |
0~300℃ |
||
加热器 |
不锈钢加热管,2.0KW×2 |
||
出口温度♀传感器 |
K型热电偶 |
||
温度调节精度 |
入口温度±1℃ |
||
构成 |
干燥室 |
大小 |
内径457×高975mm(玻璃部分) |
材质 |
干燥室、旋风部、生成物容器:超硬玻璃制,其它配管材料为不锈钢及硅胶软管 |
||
喷嘴附加结构 |
筛眼自动清扫(探针敲击),前端附着粉末去除(喷嘴吹风) |
||
机身︼附加结构 |
头部(热风吹出部)的自动升降(洗净干燥室时使用) |
||
计装器 |
调节功能:入口温度、热风量、泵送液量、喷雾空气压、筛眼清扫时间 指示计:入口温度、出口温度、干燥空气、风量计、喷雾空气压力计 |
||
过升防止结构 |
加热器室侧面设有独立过升防止器 |
||
外部输出 |
入口温度、出口温度输出(4~20mA) |
||
收集容器承载台 |
标准装配 |
||
除静电刷 |
标准装配 |
||
安全罩 |
标准装配 |
||
安全功能 |
入口、出口温度过热、送液泵反转功▃能、过电流漏电保护开关 |
||
规格 |
外形尺寸 |
W1060×D880×H1770mm |
|
重量 |
约180kg |
||
电源(50/60Hz)额定电流 |
AC220V 24A |
||
附属品 |
硅胶送液软管(外径6.4mm×内径3.2mm×长2m)1根、进气软管(内径7.9mm×长3m)1根、排气软管(内径50mm×长3m)1根 |
||
选购品 |
有机溶剂回收装置(GAS410) |
电源插头不附属,外形尺寸不╱含突出部分。 ●配套空气压缩机的要求:喷出空气∞量20L/min以上,喷出压力0~294KPa(3Kg/cm2),需要带减压阀。 ●本装置不是防爆结构,使用时请注意。 ●有机溶剂使用时,需要和溶剂回收装置GAS410一起配套使用。 电源线长度为2m。()为设备总开关的电流容量。 |
系统图: |
|||
|
|||
操作性: |
控制面: |
||
|
|||
干燥时间: |
|||
应用例: |
|||
|
日本YAMATO实验室大型喷雾干燥机Spray Dryer |
DL41 |
|
Fine particles of100μm areproduced. The DL41 is a spraydryerwhich can produce fine particle of 40 to 100μm, whichwereconsidered to be extremely difficult to produceinlaboratories.DL41是喷雾干燥仪的一种,可以制造出100微米的颗粒,在实验室中这个标准被认为极难达到。
|
Control panel |
|
||||||||||||||||||||||||||||||||||||||||||
Easy operation and maintenance | |||||||||||||||||||||||||||||||||||||||||||
The hot airinletand drying chamber cover automatically move up and down, andsincethecyclone and product vessel can easily be removed, cleaningatthe finish of your experiment is easy.
Controlfunctionsare convenintly arranged on the control panel forvariousconditions.
|
|
||||||||||||||||||||||||||||||||||||||||||
Sprayingnozzle | |||||||||||||||||||||||||||||||||||||||||||
Nozzlesize (µm)
|
|||||||||||||||||||||||||||||||||||||||||||
Liquidnozzle(F) |
Air nozzle(A) |
||||||||||||||||||||||||||||||||||||||||||
Systemdiagram |
Specifications | ||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||