全自动聚乙烯压痕硬度测定仪
Full automatic polyethylene indentation hardness tester
SLYQ-96A/3路
SLYQ-96A/3 Road
一、满足标准：
One, meet the standards:
GB/T 23257-2009 埋地钢质管道聚乙烯防腐层
GB/T 23257-2009 polyethylene coating for buried steel pipeline
二、产品概述：
Two, product overview:
本仪器主要测试聚乙烯在一定的温度环境和恒定的压力下经过一定的时间后的压痕深度。
The instrument is mainly test of polyethylene in a definite temperature environment and the constant pressure after indentation depth after a certain time.
本仪器是国内自动化程度最高，最领先的测试聚乙烯压痕硬█度的测试仪器，由于做的时间比←较长，试验人员只需要在试验前设定好参数后，会自动根据设置的实验条件进行加温，并保持恒温，能够自动加载，并自动采集结果、计算平均数值。实验完成后有报□警提示，报警时间长短可以设定!
This instrument is the highest degree of automation, test instrument most leading testing polyethylene indentation hardness, as a result of the relatively long time, test personnel only need to set parameters in the test before and after, will automatically according to the experimental conditions set for heating, and keep constant temperature, automatic loading, automatic acquisition and calculation results, the average values. After completion of the experiment has alarm, alarm time can be set!
全自动聚乙烯压痕硬度测定仪
三、产品特点：
Three, product features:
1、本仪器核心控制部分通过7寸触摸屏设置参数并︼控制。
1, the instrument is the core control part through a 7 Inch Touch screen set up parameters and control.
2、本仪器变形采集利用的微型位移传感器技术，淘汰了利用数字千分表采集位移精度低、易坏及需要更换电池等缺陷
2, the collection and utilization of micro displacement sensor deformation technology leading, eliminated using digital micrometer acquisition displacement precision is low, easily broken and the need to replace the battery and other defects
3、设置好参数后，点开始实验后自动加载，实验结束后自动计算结果，同时压头自动复位到初始位置进行下次实验
3, after parameter setting, some began to automatic loading experiment, automatic calculation results after the experiment, at the same time indenter automatic reset to the initial position for the next experiment
同时可以∮做三路实验，也可以单独进行一路或二路
At the same time can do three experiments, can also be a road or two separate
本仪器带有微型打印机，可以对试验结果进行打印，并自动计算平均值。
The instrument with a micro printer, you can print the test results, and automatic calculation of average value.
测试环境温度为：室温-100度，温度可设定
The test environment temperature: room temperature -100 degrees, the temperature can be set
具有报警提示，实◣验完成后根据设定的报警时间进行报警。
With alarm, after completion of the experiment according to the set alarm time and alarm.
四、技术参数：
Four, the technical parameters:
1、试验负荷：10MP(25N)
1, the test load (25N): 10MP
2、压头直径：Ф1.8mm
2, the pressure head diameter: 1.8mm
3、控温精度：±0.5度
3, temperature control precision is ± 0.5 degrees:
4、压☆痕深度指示最小分度值：0.01mm
4, the indentation depth indicates the minimum scale value: 0.01mm
5、耐压时间：可以设定
5, pressure time: you can set
6、主机变形量：≤0.04mm
6, the host deformation: ≤ 0.04mm
7、测量范围有效值：可以设定
7, the effective value measurement range: can be set
8、允许最大◢试样厚度：50MM
8, to allow maximum thickness: 50MM
五、主要配置及附件：
Five, the main configuration and accessories:
1、主 机： 一台
1, the main machine: a
2、主机压头￠1.8mm： 三个
2, the host head - 1.8mm: three
3、微型打印机： 一台
3, micro printer: a
4、自动加载装置： 三套
4, automatic loading device: three sets
5、位移传感器： 三个
5, the displacement sensor: Three
6、恒温加热装置： 一套
6, a constant temperature heating device: a
7、使用说明书： 一份
7, the use of manual: a
8、德国西门子PLC： 一个
8, Germany Siemens PLC: a
9、德国西ㄨ门子采集模块：一个
9, Germany Siemens acquisition module: a
10、寸彩色触摸※屏： 一个
10, inch color touch screen: a
全自动聚乙烯压痕硬度测定仪
